Maiden Flight Open the app

Maiden Flight

RC airplane glossary

135 RC terms explained in plain English.

1RSS / 2RSS (RSSI 1, RSSI 2, antenna RSSI)

Signal strength in dBm at the receiver, one value per receiver antenna.

These are telemetry sensors sent back by an ExpressLRS or Crossfire receiver. 1RSS is what the first antenna hears and 2RSS the second one on a diversity receiver. Values are negative: closer to zero is a stronger signal. A receiver with one antenna usually reports only 1RSS, or both with the same value.

Example: -45 dBm on the bench is strong; numbers approaching the sensitivity limit of your packet rate mean you are near the edge of range.

2-position switch (2-pos, two-position switch, toggle)

A latching switch with two positions that stays where you leave it.

Used as a source in EdgeTX, a 2-position switch reads -100 when UP and +100 when DOWN. Because it latches, it is the right type for jobs that must hold their state: throttle cut, arming, retracts and flaps on simpler models. Do not confuse it with a momentary button, which springs back.

Example: On a TX16S MKII, SF is the only 2-position latching switch, which makes it the natural throttle cut.

3-position switch (3-pos, three-position switch)

A latching switch with UP, MID and DOWN positions.

As a source in EdgeTX it reads UP = -100, MID = 0 and DOWN = +100. That makes it a ready-made three-step control: rates, flight modes, flap stages or gear with doors. When you use one as an on/off condition, decide which positions count as on, because a mix on a switch position only follows that one position.

Example: Flaps on SC: UP = flaps up (-100), MID = take-off (0), DOWN = landing (+100), shaped by a curve if the steps are uneven.

ACCESS (FrSky ACCESS)

FrSky's newer proprietary 2.4 GHz protocol, used by its ACCESS radios and modules.

ACCESS is FrSky's successor to ACCST D16. It needs FrSky ACCESS hardware on the transmitter side, typically an ACCESS-capable external module on a RadioMaster radio. A CC2500 or 4-in-1 multi-protocol module does not give you ACCESS, so check before buying ACCESS receivers.

Adverse yaw

The nose swinging away from the turn when you apply aileron.

The aileron that goes down makes more drag than the one that goes up, so the plane yaws the wrong way for a moment as it rolls. Scale models, gliders and long thin wings show it most. You reduce it with aileron differential or by feeding in a little rudder with the aileron.

AETR channel order (channel order, AETR, channel map)

Aileron, Elevator, Throttle, Rudder on channels 1 to 4: the usual EdgeTX and ExpressLRS order.

Channel order decides which output number carries which control. EdgeTX has a default channel order in the radio settings that it uses when you create a new model, so set it once before building models. The order only matters for where the plugs go and for receivers or flight controllers that expect a fixed layout.

Example: With AETR, the throttle (ESC) plugs into receiver output 3.

Aileron (ailerons)

The hinged surfaces near the wing tips that roll the airplane.

One aileron goes up while the other goes down, which banks the plane. A single servo with a split linkage works on simple models; two servos, one per wing, need either a Y-lead or (better) their own channels so you can add differential, flaperons or crow. Stick right must raise the right aileron.

Aircraft Type (wing type, tail type)

Where you tell a Spektrum radio how the wing and tail are built.

Set it first, before any other programming: it creates the mixes and channels for flaperons, dual ailerons, flaps, elevons, V-tails and so on. The A and B versions of Elevon and V-Tail mix in opposite directions, so if one is wrong, try the other.

AirWare (Spektrum AirWare)

The software that runs Spektrum DX, NX and iX transmitters.

AirWare is Spektrum's name for its transmitter firmware. DX and NX radios run it directly with a scroll wheel and buttons; iX radios run it as an Android app on a touch screen. The menus are the same idea on both but are named differently: System Setup and Function List on NX and DX, Model Setup and Model Adjust on iX.

Antenna polarisation (antenna orientation, antenna placement)

Which way the antennas point; mismatched orientation costs signal.

Simple whip antennas send and receive best side-on and worst off their tip. On a two-antenna receiver, mount them at roughly 90 degrees to each other so at least one is well placed in any attitude. Keep them away from carbon, metal and wiring, and do not aim the radio antenna tip straight at the plane.

Arming (arm switch, motor arm)

Making the motor live on purpose with a switch, and dead again with the same switch.

On an electric plane the motor can start the moment the stick moves, so many pilots keep the throttle cut active until they flip an arm switch. In EdgeTX this is built from a throttle cut Special Function on a latching switch, often with a voice callout. Set a power-up switch warning so the radio complains if the model is armed at switch-on.

AS3X (AS3X+, artificial stabilization)

A gyro in Spektrum receivers that cancels bumps and gusts.

AS3X damps out disturbances on roll, pitch and yaw so the airplane feels bigger and more locked in. It does not level the airplane; that is SAFE. Too much gain makes the airplane wobble, especially at speed. Set up with no open mixes on flight surfaces, using the Aircraft Type wing and tail options.

BEC (battery eliminator circuit, UBEC)

A regulator that powers the receiver and servos from the flight battery.

Most ESCs have a BEC built in and send about 5 to 6 V up the throttle lead. Each BEC has a current limit; lots of servos, big digital servos or retracts can exceed it and brown the receiver out. A separate UBEC or receiver pack fixes that on larger models.

Bind (binding, pairing)

Pairing a receiver with a transmitter so it only listens to that radio.

The method depends on the system. FrSky-style receivers usually use a bind button and the module's Bind menu item. An ExpressLRS receiver enters bind mode after three quick power cycles, or skips binding altogether when both ends share a binding phrase. After binding, set failsafe and check every control.

Binding phrase (bind phrase, UID)

An ExpressLRS passphrase; matching phrases on module and receiver connect without binding.

The phrase is turned into a unique ID stored in the firmware or set through the web UI. Anything flashed with your phrase links to your module automatically. Pick something unique to you, and keep using Model Match so one receiver cannot respond to the wrong model memory.

BNF (Bind-N-Fly) (Bind-N-Fly, Bind and Fly)

An airplane sold with the receiver fitted; you bind your own radio.

E-flite and other Horizon BNF airplanes come with a Spektrum receiver already installed and set up. You create a model, set it up from the manual's table (or load the Smart Transmitter File on radios that support it), and bind. AS3X and SAFE are part of the receiver, so they need a Spektrum-compatible DSMX link.

Bungee launch (hi-start, bungee)

Launching a glider or light model with a stretched elastic line and a tow hook.

The model is released into the wind and climbs like a kite until it slides off the line. The tow hook position relative to the CG matters a lot: too far back and it zooms or snaps sideways. Plenty of pilots add a launch flight mode with a little up elevator and camber.

C rating (discharge rating)

A LiPo's claimed maximum discharge, as a multiple of its capacity.

A 2200 mAh pack rated 30C claims 2.2 A x 30 = 66 A. Treat the number as optimistic marketing; a pack that gets hot or puffs after flights is being worked too hard. Choose the pack so the motor's full-throttle current sits comfortably under the rating.

Example: 2200 mAh 3S 40C: claimed 88 A, but plan for well under that.

Calculated sensor (calc sensor, computed sensor)

A telemetry sensor EdgeTX builds from other sensors, such as consumed mAh from current.

In the model's telemetry page you can add a sensor whose value is worked out on the radio: a sum, a minimum or maximum, a cell value, consumption from a current sensor, distance and so on. It then behaves like any other sensor for logical switches, voice calls and widgets. The list of formulas varies a little between EdgeTX versions.

Camber (camber mode, thermal camber)

Drooping the trailing-edge surfaces a little for more lift at low speed.

On a full-house wing, lowering ailerons and flaps together by a few millimetres makes the wing slower and floatier, which helps thermalling and gentle landings. It is usually set per flight mode or on a slider. Expect a small pitch change that needs elevator trim or compensation.

CC2500 (CC2500 module, CC2500-only)

A 2.4 GHz radio chip used in cheaper RadioMaster versions for FrSky-type protocols.

A CC2500-only radio or module covers FrSky D8 and D16 and a handful of other protocols built on that chip, such as S-FHSS. It cannot talk to systems that use different chips, such as FlySky. For those you need a full 4-in-1 multi-protocol module, or a different RF system such as ExpressLRS.

Cells (S count) (S count, 3S, 4S, series cells)

How many LiPo cells are wired in series: 3S means three cells.

Each LiPo cell is about 3.7 V nominal and 4.2 V full, so the S count sets the voltage. The motor, ESC and propeller must all suit that voltage; going up a cell spins the prop much faster and draws far more current. Check the ESC's rated cell range before plugging in.

Example: 3S = about 11.1 V nominal, 12.6 V full.

Centre of gravity (CG) (CG, center of gravity, balance point)

The balance point of the model, usually given as a distance back from the wing leading edge.

Balance the plane ready to fly, battery in, before every maiden. A tail-heavy model is twitchy and can be unrecoverable; a slightly nose-heavy one is calmer, so err nose-heavy for the first flight. Move the battery before adding weight.

Channel (CH, output channel)

One numbered output sent to the receiver, such as CH3 for throttle.

Each channel is the end result of the mixer for one output and usually drives one servo, ESC or receiver port. EdgeTX lets you mix any source into any channel, so the number is just a slot, not a fixed job. Which channels exist on the receiver, and at what resolution, depends on the RF system.

Channel Assign (RX Port Assignments, Channel Input Configuration)

Decides which switch drives which channel, and which channel goes to which receiver port.

Channel Input Configuration puts a switch or knob on a channel (for example gear on A). RX Port Assignments sends a channel to a different receiver port. Create any mix before you move a channel: the radio will not mix into a channel that has been moved.

Channel monitor (channels view, outputs monitor)

A screen that shows every channel's live value as you move sticks and switches.

This is the quickest way to see what the radio is actually sending, before blaming the receiver or a servo. Check that each stick moves the channel you expect, in the direction you expect, and that switches step where you think they do. It shows values after limits and reverse.

Clevis (quick link, kwik link)

The clip at the end of a pushrod that hooks into a horn or servo arm.

Most are threaded so you can fine-tune the pushrod length by turning them. Always fit a retaining sleeve or tube over a snap-on clevis, because a clevis that pops open in flight leaves the surface free. Metal clevises are worth using on fast or heavy models.

Companion (EdgeTX Companion)

The EdgeTX desktop program for editing, backing up and simulating models on a PC.

Companion reads and writes model and radio settings, lets you build models with a keyboard and mouse, and includes a simulator to test mixes before flying. Match the Companion version to the firmware on your radio. It is also a convenient way to keep backups.

Control horn (horn)

The arm fixed to a control surface that the pushrod connects to.

The hole you use changes the throw: an outer hole gives less movement but more leverage and precision, an inner hole gives more movement. Place the horn so its holes sit over the hinge line, which keeps up and down throw equal. It must be glued or bolted solidly; a loose horn can cause flutter.

Crossfire (TBS Crossfire)

A long-range 900 MHz RC system from TBS that introduced the CRSF protocol.

Crossfire runs as an external module on EdgeTX radios and talks to the radio over CRSF, the same link ExpressLRS uses. It needs its own receivers; ExpressLRS and Crossfire do not bind to each other. Telemetry appears as the familiar RSSI, LQ and TPWR sensors.

Crow (butterfly, crow brake)

Ailerons up and flaps down together, used as an airbrake for steep, slow landings.

The opposing surfaces create drag and lose lift at the tips, letting a glider or full-house model come down steeply without speeding up. It nearly always needs elevator compensation through a curve, because the pitch changes as crow comes in. Leave some aileron travel free so you can still roll.

CRSF (Crossfire protocol, CRSF serial)

The serial protocol between an EdgeTX radio and an ELRS or Crossfire module.

CRSF carries channel data out to the module and telemetry back to the radio, and lets the module's settings be changed through a Lua script. RadioMaster radios with internal ExpressLRS use it for the internal module. Receivers can also output CRSF to a flight controller or gyro instead of individual PWM pins.

Curve (custom curve, point curve)

A shape that maps an input value to an output value, set by points.

Curves let a control respond non-linearly: a throttle curve, a flap-to-elevator compensation that ramps with the flaps, or steps that suit a switch. On a mix line the curve is applied before weight and offset. Expo and differential are built-in curve types; custom curves are defined per model.

Example: Flap-to-elevator compensation with points 0 / 30 / 100: nothing at flaps up, a little at take-off flap, full amount at landing flap.

Custom failsafe (set failsafe, failsafe positions)

Failsafe where you choose a fixed position for each channel on signal loss.

The usual safe choice for an airplane: throttle to motor-off, surfaces near neutral or a gentle turn. Where the positions are stored depends on the system; some keep them in the radio's module settings, others in the receiver. Always test by switching the radio off with the prop removed.

Delay and slow (mix delay, slow up, slow down, servo slow)

Mix settings that wait before moving, or move gradually, when the source changes.

Delay holds the old value for a set time before the change starts; Slow spreads the change over a set time. Each has an up and a down setting: up applies when the source value rises, down when it falls. They are the first step in a mix line, before curve and weight.

Example: Retracts on a switch where DOWN = gear down: the switch value rises, so a door sequence uses Delay up.

Differential (Diff, aileron differential)

Making ailerons travel further up than down to reduce adverse yaw.

In EdgeTX it is a setting on the mix line, applied after weight and offset. Outputs reverse is applied after the mix, so if one aileron servo is reversed in Outputs, the two Diff values need opposite signs to make both surfaces go up more than down. Check it on the model, not just on the screen.

Diversity (antenna diversity, true diversity)

A receiver with two antennas that uses whichever is hearing better.

Diversity helps when one antenna is blocked by the fuselage, battery or carbon in some attitudes. On some receivers there is one radio chip switching between antennas; on others each antenna has its own chip. Either way, route the two antennas in different directions.

DSM2

The older Spektrum link that DSMX replaced.

DSM2 receivers still work with most Spektrum radios, though some EU-market radios leave it out. It is less resistant to interference than DSMX, so use DSMX receivers for anything new.

DSMX (DSM X)

Spektrum's current 2.4 GHz radio link.

DSMX is the protocol every current Spektrum transmitter and receiver uses. It hops between frequencies to avoid interference. A RadioMaster with a full 4-in-1 module can also bind DSMX receivers, but Spektrum-only features such as Forward Programming are built for Spektrum radios.

Dual rate (rates, D/R, high and low rates)

Switchable control travel: smaller movements for smooth flying, larger for aerobatics.

EdgeTX has no dedicated dual-rate menu. You add two or three lines to an Input, each with its own weight and expo and a switch position that selects it. The line order matters: EdgeTX uses the first line whose switch is active, so put a catch-all line with no switch last.

Elevator

The hinged tail surface that pitches the nose up or down.

Pull the stick back and the elevator trailing edge should go up, raising the nose. Check this on the model itself, not just on the channel monitor. Elevator is usually the most sensitive control on a model, so most pilots start with modest throws and some expo.

Elevon (delta mix, flying wing mix)

Two surfaces on a flying wing that do both aileron and elevator.

Each elevon servo gets a mix of aileron and elevator: they move together for pitch and opposite for roll. In EdgeTX this is two mix lines per channel. If pitch is right and roll is wrong (or the other way round), change the sign of one mix weight rather than reversing an output.

End points (limits) (limits, min/max, travel, ATV)

The Min and Max settings in Outputs that set how far a servo can travel each way.

In EdgeTX, Min and Max scale the whole travel rather than simply chopping it off, and they are an absolute ceiling for that channel. Use them to stop a servo binding against its linkage and to match travel on paired servos. They apply on the Outputs page, after all the mixing.

ESC (electronic speed controller, speed controller)

The controller between battery and motor that sets motor speed from the throttle channel.

Most hobby ESCs need to see low throttle at power-up before they will run the motor, and many need a one-time throttle range calibration. Many include a BEC that powers the receiver. Treat the motor as live whenever a battery is plugged in.

Expo (exponential)

Makes the stick softer around centre while keeping full travel at the ends.

Expo bends the response so small stick movements do less, which smooths out twitchy models. In EdgeTX it is set on an Input line; positive values soften the centre. It is often paired with dual rates, with more expo on high rate.

Example: Elevator 30% expo: the first part of stick movement feels gentle, but full stick still gives full throw.

ExpressLRS (ELRS) (ELRS, ExpressLRS)

An open-source RC link on 2.4 GHz or 900 MHz, built into many RadioMaster radios.

ExpressLRS offers long range and low latency, and is set up from the radio through the ExpressLRS Lua script. The transmitter module and the receiver must run the same major firmware version or they will not connect. For airplanes, pay attention to the packet rate, because the standard rates reduce the resolution of channels above 4.

External module (module bay, JR module, nano module)

A plug-in RF module in the bay on the back of the radio.

It lets one radio fly receivers from another system, such as Crossfire, a 4-in-1 multi-protocol module or a different ELRS band. Full-size radios have a JR-size bay; smaller radios use a smaller bay. Each model chooses whether it uses the internal module, the external module, or both.

Fade (flight modes) (fade in, fade out, flight mode fade)

A time over which EdgeTX blends the change when you switch flight modes.

Without fade, changing flight mode jumps straight to the new mode's settings, which can twitch the model. A fade in or fade out of a second or so smooths the transition. It is set per flight mode.

Failsafe (FS, signal loss)

What the receiver does with each output when it loses the radio signal.

Every model must have failsafe set and tested; the safe goal is motor off. The options depend on the system: hold last positions, custom positions, or stop sending pulses. On an ExpressLRS PWM receiver, failsafe is set per output in the receiver's web UI, where the default is 1500 us on all outputs except output 3 at 988 us.

Firmware (flashing, EdgeTX update, bootloader)

The software inside the radio, module or receiver; updating it is called flashing.

EdgeTX, the ELRS module and each receiver all have their own firmware versions. Back up your models and SD card before updating the radio, and match the SD card contents to the new EdgeTX version. For ELRS, update the module and receivers together so their major versions stay the same.

Flaperon (flaperons)

Ailerons that also droop together to work as flaps.

Each aileron needs its own servo and channel. The aileron mix moves them opposite, and a flap mix on a switch moves them both down. Keep enough aileron travel left over at full flap, and expect a pitch change that may need elevator compensation.

Flaps (flap)

Inboard trailing-edge surfaces that droop to add lift and drag for take-off and landing.

Flaps let the model fly slower and descend more steeply. They are usually on a 3-position switch for up, take-off and landing. Many models pitch up when flaps go down, so a flap-to-elevator compensation curve that starts at zero with flaps up is common.

Flight mode (FM, flight phase)

A named model state, picked by switch, that can have its own trims and GVAR values.

EdgeTX models have a default mode FM0 plus further modes, each turned on by a switch. A mode can change trims, fade times and global variable values, and mix lines can be limited to certain modes. When more than one mode's switch is on, EdgeTX picks one by its order in the list, so plan your switch logic.

Example: A glider with Launch, Cruise, Thermal and Speed modes on one 3-position switch plus a launch button.

Forward Programming (FP)

The receiver's own setup menu, shown on the transmitter screen.

Newer Spektrum receivers such as the AR631+ keep their AS3X, SAFE and failsafe settings inside the receiver. Forward Programming lets you change them from the radio. On NX radios it appears in the Function List once such a receiver is bound; on iX radios you switch it on first in Model Setup > Menu Setup. It works over DSMX only.

FrSky D8 / D16 (ACCST, D8, D16, FrSky X)

Older FrSky 2.4 GHz protocols supported by CC2500 and 4-in-1 modules.

D8 carries 8 channels and is used by older receivers; D16 (ACCST) carries 16. D16 has two incompatible firmware versions, so the module protocol choice must match the version flashed on the receiver. Many cheap receivers from other brands also speak these protocols.

Full Res (Full Resolution, full res packet rate)

ExpressLRS packet rates that send servo channels at full resolution (CH5 needs extra care on 3.x).

In the standard ELRS rates CH5 (AUX1) is only 2-position and AUX2 to AUX8 have reduced resolution. That is fine for switches but not for servos. If any servo is on CH5 or above (a second aileron, flaps, gear doors), choose a Full Res rate such as 100 Hz Full or 333 Hz Full. On ExpressLRS 3.x also pick Switch Mode 16ch Rate/2: in the 8ch and 12ch Mixed modes CH5 is still sent as a 2-position arm switch. ExpressLRS 4.x sends CH5 at full resolution in every Full Res mode.

Function List

The NX and DX menu for adjustments you make with the radio transmitting.

Press the scroll wheel on the main screen to open it. Servo Setup, D/R and Expo, Throttle Cut, Flap System, Mixing, Timer, Range Test, Telemetry, Forward Programming and the Monitor all live here. On iX radios the same jobs sit under Model Adjust.

Gear doors (sequenced doors, door sequencer)

Doors that must open before the retracts move and close after they finish.

The order matters: if a door closes on moving gear, something breaks. You can use a hardware sequencer or build it in EdgeTX with a logical switch, mix delays and a replace (REPL) line. Test the sequence many times on the bench, in both directions.

Gimbal (stick, stick unit)

The stick assembly that turns stick position into a control value.

Each radio has two, each covering two axes. Spring tension, the throttle ratchet or friction, and stick length can usually be adjusted. Calibrate the gimbals in the radio settings after a firmware update or if centres look off on the channel monitor.

Global function (GF, global special function)

A Special Function set in the radio settings that works in every model.

It uses the same actions as model Special Functions, such as playing a sound or adjusting volume. Use it for things you want on every model, but keep model-specific safety jobs, especially throttle cut, in the model's own Special Functions.

Global variable (GVAR) (GVAR, GV)

A named number you can use in place of a weight, offset or Diff, and change per flight mode.

Instead of typing a fixed value into several mix lines, you point them at a GVAR. Change the GVAR once and every line follows. Each flight mode can hold its own value, and a Special Function or knob can adjust it, which is handy for tuning in the air.

Example: GV1 = aileron differential, set to a different value in Thermal and Speed modes.

Gyro stabilisation (stabiliser, gyro receiver, flight controller)

A gyro that detects unwanted movement and corrects the surfaces automatically.

Gyros range from simple rate dampers to full flight controllers with self-levelling. They sit between the receiver and the servos, often fed by a serial link. Check surface correction direction on the bench every time, because a reversed gyro fights you instead of helping.

Hall sensor gimbal (hall gimbal, hall effect)

A gimbal that reads stick position with magnets instead of a wiping potentiometer.

With no rubbing contact there is little wear, so the readings stay clean for years. Most current RadioMaster radios use hall gimbals. You still need to calibrate them, and they still have mechanical springs and ratchets you can adjust.

Hand launch (hand toss)

Throwing the model into the air by hand instead of taking off from the ground.

Throw firmly and level or slightly nose-up, into the wind, with the motor at full power for most powered models. A helper makes it easier on your first flights. Make sure the throttle cut is off and the arm switch is on before you pick the model up to throw.

Hold (failsafe) (hold last position)

A failsafe mode where every output stays where it was when the signal was lost.

It sounds harmless but is risky on a powered plane: the motor keeps running at whatever throttle you had. If you use hold for surfaces, make sure the throttle channel still goes to motor-off.

Hold Last (Hold Last Command)

Failsafe mode where every channel except throttle keeps its last position.

Hold Last is the Spektrum default for the non-throttle channels, paired with SmartSafe on throttle. It is fine for most sport airplanes; channels that must go somewhere definite on signal loss (spoilers, a gear door) need Preset instead.

Input (inputs page)

The first stage in EdgeTX, where sticks get their rates, expo and switches.

Inputs take raw sources, mostly sticks, and shape them with weight, expo and curves before the mixer uses them. Several lines on one input give you dual rates. Shaping the stick here means every mix that uses the input gets the same feel.

Internal module (internal RF)

The RF system built into the radio, such as ExpressLRS or a 4-in-1.

Many RadioMaster radios come in versions with different internal modules, so check which one you have before buying receivers. Each model memory can turn the internal module on or off and set its protocol and receiver number.

The percentage of recent packets that arrived intact.

On ExpressLRS and Crossfire, LQ is often a better warning than signal strength. A steady 100% is normal close in; it drops as you fly further or behind obstacles. Set a voice warning well before the link is lost so you have time to turn back.

LiPo (lithium polymer, battery pack)

The usual flight battery: light and powerful, but it needs careful charging and storage.

Each cell is about 4.2 V full and 3.7 V nominal. Charge with a balance charger, never unattended, and store packs at storage voltage. A puffed, damaged or very hot pack should be retired safely.

Logical switch (LS, L1, virtual switch)

A virtual switch that turns on when a condition you set is true.

Conditions can compare values (a > x), combine switches (AND, OR), latch (sticky), or time things. The result, L1, L2 and so on, can be used anywhere a real switch can. This is how you build arming, sequencers and telemetry alarms.

Example: L1: a<x with the gear channel and -50, used to know when the gear is mostly up.

Lua script (Lua, tools script)

A small program on the SD card that adds screens, tools or functions to EdgeTX.

EdgeTX runs several kinds: tools scripts (such as the ExpressLRS configuration script), telemetry screens, widgets, and function or mix scripts. Copy scripts that match your EdgeTX version, and treat third-party mix scripts with care because they can drive outputs.

mAh (capacity, milliamp hours)

Battery capacity: how much charge the pack holds.

A 2200 mAh pack can supply 2.2 A for an hour, or much more for a shorter time. Many pilots land with roughly a fifth to a third left to protect the pack. A current sensor plus a calculated consumption sensor lets the radio tell you how much you have used.

Maiden flight (maiden, first flight)

The first flight of a new or rebuilt model.

Do the checks before you go: CG, control directions, throws, failsafe, range, and a full-power run on the ground. Fly in calm air, climb to a safe height, and trim for level flight before trying anything else. Land early and review.

Mix (mixer, mix line)

A line that sends a source to a channel, with its own weight, offset, curve and switch.

Each channel is built from one or more mix lines that add, multiply or replace each other. Within a line the order is delay/slow, then curve, then weight, then offset, then Diff. Outputs reverse and limits are applied later, after the mixer.

Mode 1 / Mode 2 (stick mode, Mode 2, Mode 1)

Which stick does what: Mode 2 puts throttle and rudder on the left stick.

Mode 2 (throttle and rudder left, aileron and elevator right) is common in North America. Mode 1 puts elevator on the left and throttle on the right. The throttle stick should not spring to centre, so changing modes may mean moving the ratchet as well as the setting.

Model (model memory, model file)

One saved setup in the radio for one airplane.

Each model holds its own inputs, mixes, outputs, timers, telemetry and RF settings. Use one model per airplane, even for similar planes, and select the right one before every flight. Model Match helps catch a wrong selection.

Model Match

Stops a receiver responding unless the radio has the right model selected.

The model's receiver number is sent with the link, and the receiver only accepts the number it was bound or set to. With ExpressLRS it must be turned on in the module settings. It is a simple guard against flying with another plane's trims, reverses and failsafe.

ModelMatch (Spektrum) (ModelMatch, Model Match Spektrum)

A Spektrum receiver only answers the model memory it was bound with.

ModelMatch is automatic on Spektrum radios with model memory. Bind each airplane with its own model selected and the receiver ignores the radio when any other model is chosen. Copying, resetting, importing or changing the Model Type of a model does not carry the bind over, so bind again afterwards.

Example: You copy "Timber" to make "Timber floats". The airplane does nothing on the copy until you bind it to the new model.

Momentary switch (button, push button, spring switch)

A switch or button that springs back when you let go.

Good for starting a timer, a voice callout, a drop or trainer handover. Never put throttle cut, arming or retracts on one: the moment you let go, the state changes back. Some RadioMaster radios have swappable switch modules, so check which of yours are momentary.

Multi-protocol module (4-in-1, MPM, multi module)

A module with several radio chips that speaks many brands' receiver protocols.

A 4-in-1 lets one radio fly receivers from many makers, such as FrSky D8/D16 or FlySky. A CC2500-only module covers just the protocols that chip supports. Pick the protocol and sub-protocol in the model's module settings, then bind.

No pulses (no signal failsafe)

A failsafe mode where the receiver stops sending signals to the outputs.

Many ESCs stop the motor when the signal disappears, and servos usually go limp. Not every ESC or gyro behaves the same way, so test it with the prop off. It is one option on some systems; it is not the ExpressLRS PWM receiver default.

Offset

A fixed amount added to a mix line after curve and weight.

Offset shifts the result up or down. It is how you make a switch line produce a value centred where you want, or move a range so it starts at zero. It is not the same as subtrim, which moves the servo centre on the Outputs page.

Output (outputs page, servos page)

The final stage per channel: subtrim, limits, reverse and centre before it goes to the receiver.

Outputs fix the mechanics of each servo: centre it with subtrim, set its travel with Min and Max, and reverse it if it moves the wrong way. Reverse is applied last, after all mixing. Get directions right here rather than with negative mix weights where you can.

Override channel (override, channel override)

A Special Function that forces a channel to a set value while its switch is on.

This is how EdgeTX does throttle cut. The override value is used before Outputs limits and reverse, so with CH3 reversed in Outputs, an override of -100 gives full throttle, not motor off. If several overrides on the same channel are active, the last one in the list wins, which is why cut goes at the bottom.

Packet rate (rate, Hz)

How many control packets per second the ExpressLRS link sends.

Higher rates mean lower delay; lower rates reach further. For airplanes there is a second consideration: in the standard rates, CH5 is 2-position and AUX2 to AUX8 lose resolution. Use a Full Res rate if servos sit on CH5 or higher.

Panic mode (panic button, panic recovery)

A button that makes a SAFE airplane level itself.

On SAFE airplanes, holding the panic button (the I button in Spektrum's SAFE setups) makes the receiver bring the airplane back to level flight. Let go and you have normal control again. Practise it at a safe height before you need it.

Pot (potentiometer, knob, S1, S2)

A rotary knob on the radio that gives a proportional value.

Pots read -100 at one end and +100 at the other, and can be used anywhere a source is allowed. They are handy for camber, a GVAR tweak, or volume. Some have a centre detent.

Preset failsafe (Preset)

Failsafe mode where each channel goes to a position you stored.

On classic Spektrum receivers Preset comes from a special bind sequence with the bind plug. On AR631+ and other Forward Programming receivers you set it per channel in Forward Programming > Other Settings > Failsafe. If throttle is not on CH1, use Preset so it still goes low.

Propeller (prop, 10x6)

The propeller, sized by diameter and pitch, such as 10x6.

A bigger diameter or more pitch loads the motor more and draws more current. Check the motor maker's suggested sizes for your cell count. Take the prop off whenever you work on the radio or the model on the bench.

Pushrod (linkage, control rod)

The rod or wire that connects a servo arm to a control horn.

A good linkage is stiff, has no slop and does not bind anywhere in its travel. Long pushrods should be supported along their length so they cannot flex. Most free play in a control surface comes from loose pushrod ends.

PWM receiver (PWM)

A receiver with a separate output pin for each servo or ESC.

Each output sends a pulse, typically around 1000 to 2000 us wide, that sets the servo position. Most fixed-wing models use one. Check how many PWM outputs it has and which channels map to them.

Range check (walk-out test, range test)

A ground test at reduced power to make sure the link is healthy before flying.

Some modules have a range check mode in the model settings that cuts power. With ExpressLRS, a common method is to set a low output power and walk away, watching LQ and controls. Do it with the model in its flying shape so antenna placement is tested too.

Rate tuning

Adjusting throws and expo after flying until the model feels right.

Start with the recommended throws, then change one thing at a time. If the plane is twitchy, reduce rate or add expo; if it feels sluggish at full stick, add rate. Small changes of 5% are easier to judge than big jumps.

Receiver number (RX number, model ID)

The number that ties a receiver to one model memory.

It is set in the model's module settings and used by Model Match. Give each model its own number. Changing it later may mean rebinding or reconfiguring the receiver.

Reflex (speed mode)

Raising the trailing-edge surfaces slightly to reduce lift and drag for speed.

It is the opposite of camber. Gliders use a little reflex in a speed mode; flying wings use reflex built into the elevon trim to stay stable in pitch. Small amounts go a long way.

Retracts (retractable gear, landing gear, gear)

Landing gear that folds away in flight and comes back down for landing.

Retracts belong on a latching switch, never a momentary button, so the gear cannot change state when you let go. Decide on purpose what failsafe does with the gear channel; many pilots choose gear down. A Slow on the gear mix gives a scale-looking movement with servo-type retracts, while electric units usually set their own speed.

Reverse (servo reverse, invert, direction)

Flips a channel's direction on the Outputs page.

Use it when a servo moves the wrong way for every input, which is a mechanical fix rather than a mixing one. Reverse is applied last, after the mixer. Special Function overrides are applied before it, so reversing the throttle channel also flips what a throttle cut value means.

Example: CH3 reversed in Outputs: a cut override of -100 would run the motor at full power, so the cut value must be +100.

RQly (uplink link quality, RX quality)

Link quality measured at the receiver: how well the plane hears the radio.

ExpressLRS and Crossfire report it as a percentage. This is the direction that matters most, because it is your control link. It is a good sensor to put a voice alarm on, set high enough to give you time to turn back.

RSSI (signal strength, received signal strength)

Received signal strength: a rough guide to how far you are from the range limit.

Different systems report it differently. FrSky-type receivers send a single RSSI number, while ExpressLRS and Crossfire report 1RSS and 2RSS in dBm. Signal strength can drop quickly behind trees or the airframe, so read it together with link quality rather than on its own.

Rudder

The hinged surface on the fin that swings the nose left or right.

Left stick should move the rudder trailing edge to the left. Rudder co-ordinates turns, holds the line in crosswind landings, and on many models also steers the tail or nose wheel on the ground. Some models need a little rudder mixed with aileron to turn cleanly.

SAFE (SAFE technology, Envelope, self-leveling)

Spektrum's attitude limits and self-levelling on top of AS3X.

SAFE can stop the airplane banking or pitching past set angles (envelope) and level the wings when you let go of the sticks. A flight-mode switch picks how much help you get, often from beginner to fully off. On AR631+ receivers it is set up in Forward Programming with First Time SAFE Setup.

Example: A trainer on a 3-position switch B: beginner with tight limits, intermediate with wider limits, experienced with SAFE off and AS3X only.

SAFE Select

E-flite's on/off switch for SAFE on Bind-N-Fly airplanes.

SAFE Select is turned on or off as part of the bind, and can be put on a switch. On current E-flite BNFs you assign it by holding both sticks in the bottom inside corners and flicking the chosen switch five times (channels 5 to 9 only), or through Forward Programming. At power-up the surfaces wiggle twice when it is on and once when it is off.

SBUS (S.BUS, S-BUS)

A serial protocol that carries up to 16 channels on a single wire.

A receiver with an SBUS output can feed a gyro, flight controller, SBUS servos or an SBUS-to-PWM decoder with one lead. It saves wiring in big models, but only devices that understand SBUS can use it. Many FrSky-type receivers offer it; ExpressLRS receivers usually use CRSF instead, with SBUS as an option on some.

SD card (microSD, SD contents)

The memory card inside the radio: sounds, scripts, images, backups and model files.

EdgeTX expects a particular folder layout on the card, and the sound pack and scripts should match the firmware version you run. Back up the whole card before any update. If voice callouts or the ExpressLRS script go missing, the SD card is the first place to look.

Sensor (telemetry sensor)

One telemetry value from the model, such as receiver voltage or link quality.

Sensors appear in the model's telemetry page after you search for new ones with the receiver powered. You can rename them, change units or ratios, and use them in logical switches, voice calls and widgets. Delete sensors you no longer have so old values do not confuse you.

Sequencer

A Function List tool that runs channels in a timed order from one switch.

The usual job is gear doors: one switch opens the doors, then lowers the gear, then closes the doors, with set timing. The number of sequencers depends on the radio (NX8 two, NX10 four). Test it with the airplane on a stand.

Serial receiver (CRSF receiver, serial RX)

A receiver that sends all channels over one serial link instead of separate servo pins.

Serial receivers are tiny and are meant to plug into a flight controller or gyro, which then drives the servos. The common protocols are CRSF and SBUS. For a plain airplane with no stabiliser you normally want a PWM receiver instead.

Servo

The small motor unit that moves a control surface to the position the receiver asks for.

Servos are chosen by torque, speed, size and gear type; larger and faster models need stronger servos and metal gears. A servo that buzzes hard at rest is usually being pushed against a stop, which drains power and can overheat it. Check travel limits so nothing binds.

Servo arm (servo horn, output arm)

The arm on the servo output shaft that the pushrod connects to.

A hole further out gives more throw but less precision and leverage; a hole closer in does the opposite. With the servo centred, the arm should sit close to 90 degrees to the pushrod so both directions move the same amount. Always refit the arm screw.

Servo centering (centring servos, neutral)

Setting each servo to neutral before fitting the arm and linkage.

Power the receiver and servos from the radio with trims and subtrim at zero, then fit the arm as near square as the splines allow. Adjust the clevis to make the surface neutral. Subtrim is for the last small correction, not for fixing an arm that is a spline or two off.

Slider (side slider, LS, RS)

A sliding control on the side or back of the radio that gives a proportional value.

Sliders work like pots, reading -100 at one end and +100 at the other, and you can reach them without letting go of the sticks. They suit camber, a flap trim, or tuning a GVAR in the air. Not every radio has them.

Smart (ESC and battery) (Smart Technology, Smart ESC, Smart battery, Smart Throttle)

Spektrum ESCs and batteries that send their data to the radio.

A Smart ESC on a Smart-capable receiver sends flight pack voltage and other data back through the throttle lead, so you can set a low-voltage alarm without a separate sensor. Smart batteries also report their own information. Telemetry Auto-Config picks them up.

SmartSafe (Smart Safe)

Spektrum's throttle failsafe: no motor until the throttle is low, and low throttle if the link drops.

SmartSafe looks after the throttle channel only. The ESC gets no throttle signal while the transmitter is off and can't arm until the throttle is low. If the link drops, the throttle goes to the position it was in at bind, so bind with the stick fully down. Other channels use Hold Last or Preset.

Snap-flap (elevator to flap, snap flap)

Flaps (and sometimes ailerons) that move with up elevator for tighter turns.

A mix from elevator into the flap channels adds camber when you pull, which tightens the turn. It is popular on gliders, pattern and combat models. Start with a small amount, often only on up elevator, and limit it to the flight modes where you want it.

Special function (SF, custom function)

A per-model action that runs while a switch is on: override a channel, play a sound, reset a timer.

Special Functions are checked from top to bottom. When more than one override on the same channel is active, the last one in the list wins, so the throttle cut belongs at the bottom where nothing can override it. They are also where voice callouts and logging are set up.

Stall

Loss of lift when the wing meets the air at too steep an angle, often from flying too slowly.

A stall is about angle, not just speed, so a hard pull can stall a fast plane too. The usual warning signs are mushy controls and the nose dropping. Recovery is to ease off the up elevator, level the wings, and add power once flying speed returns.

Subtrim (sub-trim, centre offset)

A small adjustment to a servo's centre on the Outputs page.

Subtrim moves the neutral point of one channel without touching the stick trims. Keep it small: large subtrim makes the travel uneven either side of centre. If you need a lot, re-centre the servo arm or adjust the clevis instead.

Switch warning (power-up warning, startup check, pre-flight checks)

A check at model load that warns you if switches are not where you set them.

You choose the expected position for each switch in the model setup. Set the throttle cut switch so the radio complains unless it is in the cut position at power-up. Exact menu wording varies between EdgeTX versions.

System Setup (Model Setup (iX))

The NX and DX menu for model-level settings, used with the radio not transmitting.

Hold the scroll wheel while switching on, or choose System Setup from the Function List. Model Select, Model Type, Aircraft Type, Channel Assign, flight modes, warnings and bind live here. The iX equivalent is Model Setup, which asks you to turn the RF off first.

TAER channel order (TAER, Spektrum channel order)

Throttle, Aileron, Elevator, Rudder on channels 1 to 4: Spektrum's order.

Spektrum radios and receivers use throttle on CH1, aileron CH2, elevator CH3, rudder CH4, gear CH5 and Aux 1 CH6. A second aileron or a flap usually goes on CH6. RadioMaster setups in Maiden Flight use AETR, so the ESC sits in a different port.

Example: With TAER the ESC plugs into receiver port 1 (THRO).

Telemetry (downlink)

Data sent from the model back to the radio: link quality, voltages and more.

With telemetry the radio can warn you about a weak link or a low battery before it becomes a problem. What you get depends on the receiver and any sensors fitted. Set voice alarms for the values that matter, because you will not be looking at the screen while flying.

Telemetry ratio (TLM ratio, telem ratio)

How often an ExpressLRS link uses a packet to send telemetry back.

Each telemetry packet takes the place of a control packet, so a higher ratio gives fresher telemetry at the cost of a little control rate. The ExpressLRS Lua script lets you change it. The default settings suit most airplanes.

Throttle cut (motor cut, cut switch, throttle hold)

A latching switch that forces the throttle channel to motor-off.

In EdgeTX it is an Override Special Function on the throttle channel, placed at the bottom of the list. The override is applied before reverse, so if CH3 is reversed in Outputs the cut value must be +100, not -100. It must be on a latching switch, never a momentary button, and you should test it on every new model with the prop off.

Throws (control throws, surface travel, deflection)

How far each control surface moves, given in millimetres or degrees.

Manuals usually give throws for low and high rate. Measure where the manual says, normally at the widest part of the surface by the trailing edge, with the radio switched to the rate you are checking. Get close mechanically first, then fine-tune with weights and limits.

Timer (flight timer)

A count-up or count-down timer that can run from a switch or the throttle.

Most pilots use a count-down timer to know when to land. A timer that runs in proportion to throttle (TH%) tracks battery use better than one that runs at a fixed speed. Timers can call out time remaining and be reset by a Special Function.

Tip stall

One wing tip stalls before the rest of the wing and the model drops a wing suddenly.

It shows up most when slow and turning, such as on the final turn to land. Tapered wings and tail-heavy models are more prone to it. Keep speed up near the ground, and if a wing drops, release the up elevator before using aileron.

TPWR (TX power, output power)

The power the transmitter module is currently sending at, shown as telemetry.

ExpressLRS and Crossfire report it in milliwatts. With dynamic power the value rises as the link needs it, which is a useful hint that the link is working hard. Higher power uses more radio battery and heats the module.

Trainer mode (buddy box, trainer)

Linking two radios so an instructor can hand control to a student and take it back.

The instructor's radio sends the signal and holds a switch, usually a momentary one, that gives control to the student. The link can be a cable or wireless, depending on the radios. Check all controls in both directions on the ground before flying with it.

Trim (trims, digital trim, stick trim)

Small buttons beside the sticks that nudge the control centre point.

Trims let you fix a model that climbs, dives or turns on its own. EdgeTX trims are digital and stored with the model, and each flight mode can keep its own. After trimming, many pilots move the correction into the linkage or subtrim and zero the trims again.

Trim flight (trimming flight)

Flying to adjust the trims until the model flies straight and level hands-off.

At a safe height and about half to two thirds throttle, trim out any climb, dive or turn one axis at a time. Land and note how many clicks you used. Large trim usually points to a mechanical or CG issue worth fixing.

Trims per flight mode (flight mode trims)

Each flight mode can keep its own trim values or share those of another mode.

Separate trims help when a model needs different settings in, say, a launch mode and a cruise mode. Sharing trims keeps things simple when modes only change rates. You choose this for each trim in each flight mode.

V-tail (ruddervator, ruddervators, V-tail mix)

Two angled tail surfaces that do the work of both elevator and rudder.

Each surface is driven by a mix of elevator and rudder: both move together for pitch and opposite for yaw. In EdgeTX that is two mix lines per channel. If one control works and the other is backwards, change the sign of one mix weight instead of reversing an output.

Weight (mix weight, rate)

The percentage that scales an input or mix line.

Weight sets how much of the source passes through: 100% is all of it, 50% is half. A negative weight flips the direction of that one line only, which is how elevon and V-tail mixes get their opposite movement. In a mix it is applied after the curve and before the offset.

Widget (main view widget)

A box on a colour-screen radio's main view showing a value, timer or script.

Colour EdgeTX radios let you lay out the main screens with widgets such as a timer, a telemetry value or a model picture. Some widgets are Lua scripts from the SD card. Black-and-white radios use telemetry screens instead.

Open this in Maiden Flight Free to start. Works on phone and computer.