RC airplane troubleshooting
Common problems and what to check, in order. The app walks you through each one with questions.
Receiver won't bind / slow-blinking LED EdgeTX
- Check the radio is set to the right protocol (CRSF for ELRS, the correct multi-protocol type for others).
- ELRS: transmitter module and receiver must share a major firmware version (3.x with 3.x) and binding phrase.
- Put the receiver in bind mode (ELRS: power-cycle 3×), then select Bind on the radio.
- Keep the radio about 1 m away during binding. Very close range can sometimes fail.
Receiver won't bind / LED keeps flashing Spektrum
- A flashing LED means the receiver is in bind mode and waiting. It goes solid once it is bound.
- Order matters. Switch off any transmitter this receiver was bound to before. A Spektrum receiver will not go into bind mode if a transmitter it knows was on before it.
- Select the right model on the radio first (ModelMatch binds the receiver to that model).
- Throttle stick and trim fully down, other controls where you want them on failsafe.
- Receiver into bind mode: hold its bind button while powering up, or use the bind plug. Then start Bind on the radio (System Setup > Bind or Function List > Bind on NX and DX; Model Setup > Bind or the BIND button on iX). On older DX radios you can instead hold the Bind button while switching on.
- Once the LED is solid, take the bind plug out. Left in, the receiver goes back into bind mode at every power-up.
- Spektrum radios speak DSMX and DSM2 only. FrSky, FlySky or ExpressLRS receivers will never bind to them.
Airplane won't respond after selecting a model (ModelMatch) Spektrum
- The receiver only answers the model memory it was bound with. Check the model name on the main screen.
- You copied a model, reset it, imported a model file or changed its Model Type? The bind does not come with it. Bind the receiver again with this model selected.
- Made a new model for an airplane you already fly? Same thing: bind again.
- If the airplane responds on another model, that other model is the one it is bound to. Pick one and stick with it.
Servos work but motor won't spin EdgeTX
- Throttle cut switch may be active. Flip it to the run position.
- The ESC will not arm unless throttle is fully low at power-up. Lower the stick and the throttle trim.
- Check the ESC signal lead is on CH3 (throttle) and the right way round.
- Some ESCs need throttle range calibration. Follow the ESC manual WITH THE PROP REMOVED.
Servos work but motor won't arm or spin Spektrum
- Throttle Cut is on. Flip H to the run position.
- SmartSafe: the ESC will not arm until it sees low throttle. Put the stick and the throttle trim fully down.
- Order: transmitter on first, wait about 5 seconds, then connect the battery and keep the airplane still while it starts.
- Spektrum puts throttle on CH1, so the ESC goes in port 1 (THRO), not port 3 like on many other radios.
- If you reversed throttle or changed its travel after binding, re-bind with the throttle fully down.
- Some ESCs need a throttle range calibration. Follow the ESC manual WITH THE PROP REMOVED.
A surface moves the wrong way EdgeTX
- Run the control-surface direction check in Safety.
- Reverse the channel on the Outputs page (Direction: INV).
- If ONE elevon on a flying wing is wrong, the mix weights need fixing, not a single reverse. See the Pro mixer guides.
A surface moves the wrong way Spektrum
- Run the control-surface direction check in Safety.
- Reverse it in Servo Setup > Reverse (Function List on NX and DX, Model Adjust on iX).
- V-tail or flying wing: try the other Aircraft Type version first (V-Tail A or B, Elevon A or B).
- If ONE of two mixed surfaces is wrong, don't reverse it on its own. See "Flying wing or V-tail: mixed surfaces move wrong".
- After reversing, re-bind so failsafe is stored again. On AS3X or SAFE receivers, run Relearn Servo Settings in Forward Programming too.
- DXS: reversing is done with trim programming at power-up (see the DXS manual).
Surfaces fine from the sticks, but the gyro corrects the wrong way Spektrum
- Do NOT fly. A gyro correcting the wrong way will roll or pitch the airplane harder and harder.
- Check: tilt the nose down and the elevator must go UP; roll the right wing down and the right aileron must go DOWN (the gyro pushes back).
- AR631+ receivers learn the servo directions during First Time Setup. Changed reversing in the radio since? Run Forward Programming > Gyro Settings > System Setup > Relearn Servo Settings.
- Use the Gyro Response Test in the Utilities menu of Forward Programming to check each axis.
- Receiver mounted differently from when it was set up (turned or upside down): redo the orientation step in First Time Setup.
- Older AS3X receivers without Forward Programming: check that receiver's manual for how it learns directions.
Servos twitch or jitter
- Low receiver voltage or a weak BEC is the most common cause. Check RxBatt telemetry under load.
- Move the receiver and antennas away from ESC and motor wires.
- A worn servo or a binding linkage can also cause jitter.
More fixes in Maiden Flight Pro
- Failsafe triggered in flight / link drops
- Failsafe triggered in flight / link drops
- No telemetry on the radio
- No telemetry on the radio
- Servo on CH5+ only snaps between two positions or steps (ELRS)
- Trim does nothing on a mixed surface
- Trims jump when switching flight modes
- Surface stops short / channel flat-tops before full stick
- A copied model won't control the airplane
- Telemetry values wrong after a receiver or sensor change
- Throttle warning won't clear at power-up
- Flying wing: elevons mixed wrong
- Flying wing or V-tail: mixed surfaces move wrong
- AS3X or SAFE acting strangely
Open this in Maiden Flight Free to start. Works on phone and computer.