RC airplane safety checks
Safety checks are always free in Maiden Flight. Do them with the propeller off.
Pre-flight safety checklist
Run this every flight session, every airplane.
- Transmitter on FIRST, then plug in the flight battery. Unplug the flight battery FIRST, then turn the transmitter off.
- Confirm the correct model is selected on the radio (model name on the main screen).
- Throttle stick fully down and throttle cut / arm switch in the CUT (safe) position before connecting the battery.
- Stand behind or beside the propeller arc, never in front of it, whenever a battery is connected.
- Check every control surface moves the correct way (see the direction check below).
- Check failsafe: motor must stop when the transmitter is switched off.
- Check battery voltage, prop tightness, and that the CG is where the manual says.
- Do a link check (range check or walk-out test) before the first flight of the day.
Failsafe: set it and test it EdgeTX
If the radio link drops, the motor must go to idle/off. Never leave failsafe at "hold last position" on an electric plane.
- Remove the propeller before testing.
- ExpressLRS (ELRS) PWM receivers: failsafe positions are set per output in the receiver's Wi-Fi web UI (PWM Output page). Out of the box every output fails to 1500 us (centre) except output 3, which fails to 988 us (throttle low). If your throttle is not on output 3, or anything else (gear, doors, flaps, a second motor) must not go to centre, set those failsafe values yourself.
- ELRS enters failsafe when link quality drops to 0, or after 1 second without a valid packet.
- Reversed throttle (CH3 reversed in Outputs): the default 988 us on output 3 is then FULL throttle. Set output 3's failsafe to the idle pulse (about 2012 us) in the receiver web UI, and test it with the propeller removed.
- FrSky / multi-protocol (4-in-1) modules: on the radio go to Model Setup > Internal/External RF > Failsafe. Choose "Custom" and set throttle (CH3) to its idle value (-100, or +100 if you reversed CH3), or "No pulses".
- Test: power up the radio, connect the battery, arm, raise throttle a little, then switch the transmitter OFF. The motor must stop within about one second.
- If the motor keeps running, do not fly. Re-check failsafe and the ESC's signal-loss behaviour.
Failsafe: set it and test it Spektrum
If the link drops, the motor must stop. On a Spektrum receiver that comes from SmartSafe, and it is stored when you bind.
- Remove the propeller before testing.
- Know what your receiver does by default. Spektrum receivers bind with SmartSafe plus Hold Last: on signal loss the throttle goes to the position it was in when you bound, and the other channels hold their last command.
- So always bind with the throttle stick and throttle trim fully down. Put the other sticks at centre and the switches in their normal flying positions.
- Preset failsafe (every channel goes to a set position) is for things like spoilers or a gear door that must not hold. On classic receivers it comes from a different bind sequence: plug in the bind plug, power the receiver, pull the plug out while the LED is still flashing, hold the sticks and switches where you want them, then turn on the transmitter. Check your receiver manual, the details vary.
- AR631+ and other Forward Programming receivers: Preset is set in Forward Programming > Other Settings > Failsafe. Pick Preset or Hold Last per channel, hold the sticks in the failsafe positions, choose Capture Failsafe Positions, then Apply. Any channel you leave alone stays on Hold Last.
- Moved the throttle to a channel other than CH1? SmartSafe only looks after the throttle channel, so use Preset failsafe and set the throttle channel low.
- E-flite BNF airplanes with SAFE: failsafe cuts the throttle and the receiver flies a gentle descending turn. Check your airplane's manual for what yours does.
- Re-bind after any change in Servo Setup (reverse, travel, sub-trim), and always after reversing the throttle. If you skip it, the stored failsafe can be FULL throttle.
- Test: restrain the airplane, prop off, arm it and raise the throttle a little, then turn the transmitter's RF off (iX radios: double-press power, choose RF off and hold OK; NX and DX radios: switch the transmitter off). The motor must stop within about a second and the surfaces must go where you expect.
- If the motor keeps running, do not fly. Re-bind with the throttle fully down and test again.
Throttle cut & arming safety EdgeTX
A switch that forces the motor off, plus a warning if the throttle is not low at power-up.
- Model Setup > Pre-start checks (called Preflight checks on some versions): enable the throttle-state warning so the radio warns you if throttle is not at idle.
- Special Functions: add a function set to "Override CH3" with value -100, and enable it. The function's trigger is the CUT position of your switch (for example SF-down), not the switch as a whole. Use a switch that stays where you leave it: SF on a TX16S or Zorro, SA on a Pocket or Boxer, SF-up on a TX12. Never use a momentary button for throttle cut.
- Flip the switch: the CH3 output on the Channel Monitor should jump to -100 regardless of the throttle stick.
- If you reversed CH3 in Outputs (some ESCs and most glow throttle servos need it): Override sets the output directly and ignores reverse, so -100 would be FULL throttle. Use +100 for the cut instead, and always prove "cut = motor off" with the propeller removed.
- Make "switch in cut position" part of your habit every time you connect or disconnect a battery.
- Never carry or work on an airplane with a battery connected and throttle cut off.
Throttle cut & arming safety Spektrum
A switch that forces the motor off in every flight mode, plus a warning if the throttle is not low at power-up.
- Use switch H for throttle cut. It is what E-flite uses on all its Spektrum setups, and on most Spektrum radios it is a 2-position switch that stays where you leave it. Check yours: it must not spring back. Never put throttle cut on the I button.
- NX and DX radios: press the roller for the Function List > Throttle Cut. Pick switch H, mark the position that cuts, and set the cut value to -100%.
- iX radios: Model Adjust > Throttle Cut. Pick H from the list (or flick it to select it), make sure only the cut position is shaded, set the value to -100 and leave Delay at 0.
- If -100 does not bring the throttle all the way down on your ESC, you may need a lower (more negative) value. That is normal on some setups.
- Prove it on the Monitor screen (in the Function List on NX and DX radios): with the cut on, the throttle channel must sit at the bottom whatever the stick does. Then prove it on the airplane with the prop off.
- Spektrum does not say whether a reversed throttle channel changes what the cut sends. If you reversed throttle (some glow servos need it), check the cut on the Monitor and with the prop off, and re-bind so failsafe is not full throttle. iX radios also have a Throttle Mode Normal/Reverse option in Aircraft Type.
- Keep the power-up throttle warning on (System Setup > Warnings on NX radios). By default it alarms if the throttle is above about 10%.
- DXS (no screen): H is already the throttle cut switch. Check which position cuts before the first flight.
- Make "H in cut" part of the habit every time you connect or disconnect a battery, and never carry the airplane with a battery in and the cut off.
Safe arming sequence (logical switches) EdgeTX
A step up from a plain throttle cut: the motor can only be enabled while the throttle is at idle, and flipping the switch back always disarms.
- Pick your arm switch: a latching 2-position switch (SF on a TX16S or Zorro, SA on a Pocket or Boxer). In this example SF-up is RUN and SF-down is CUT.
- L1: a<x, source Thr, value -97 (throttle at idle).
- L2: AND, V1 = L1, V2 = SF-up (throttle idle AND switch in run).
- L3: Sticky, V1 = L2 (set), V2 = SF-down (reset). L3 is "armed". Leave Persistent off so L3 is not remembered across power cycles.
- Important: Persistent off is not enough by itself. If you power up with SF already in RUN and the throttle at idle, L2 is true straight away and L3 arms. The switch warning in the last step is what stops that, so don't skip it.
- Special Function: !L3 > Override CH3, value -100, enabled (+100 if CH3 is reversed in Outputs: Override ignores reverse). Optional: L3 > Play track "armed" (1x).
- Test with the PROP REMOVED. Switch to run with throttle high: the motor must stay off. Lower to idle: it arms. Flip to cut: the motor stops instantly, even at full throttle.
- Model Setup > Pre-start checks: keep the throttle warning on, and set a switch warning for SF in CUT (down). The radio then makes you put SF in CUT at power-up, so you always start disarmed.
L1 a<x Thr -97 L2 AND L1 SF-up L3 Sticky V1 L2 V2 SF-down SF1 !L3 Override CH3 -100 [enabled]
Safe arming sequence (Spektrum and E-flite) Spektrum
Spektrum has no separate arm switch. Throttle cut is the safety switch, and SmartSafe stops the ESC arming until the throttle is low.
- Before you plug in: throttle stick and throttle trim fully down, H in the cut position.
- Transmitter on first. Wait about 5 seconds so it has finished starting up and is sending.
- Connect the flight battery. Keep the airplane still and upright until the receiver has started; AS3X and SAFE receivers calibrate their gyros at this point.
- The ESC then beeps (on E-flite Avian ESCs: the cell count, then a double tone). SmartSafe will not let it arm until it sees low throttle, so a throttle that is not down shows up here.
- Once the ESC is armed, the prop turns with any throttle movement as soon as the cut is off. Treat it as live from here on.
- Only flip H out of cut when you are behind the propeller and ready to taxi or launch.
- Some NX radios offer "Require Stick Low?" in the Throttle Cut menu. If yours has it, turn it on: leaving cut then needs the throttle stick at low, so the motor can't jump to whatever the stick is at.
- Afterwards: H to cut, unplug the flight battery FIRST, then switch the transmitter off.
- Test the whole sequence with the PROP REMOVED before the first flight of a new setup.
Model Match: stop flying the wrong model EdgeTX
With Model Match, a receiver ignores your radio unless the correct model is selected. Wrong-model flights are a classic cause of reversed controls and wrong throttle.
- Model Setup > Internal RF: give every model its own Receiver number.
- FrSky and multi-protocol receivers bind to that number. With a different model selected, the receiver will not respond.
- ExpressLRS: open SYS > Tools > ExpressLRS and turn Model Match on, with the airplane powered and connected. The receiver then only accepts that model ID.
- After copying a model, change the new model's receiver number before binding anything to it.
- Test: select a different model on the radio. The airplane must NOT respond to the sticks.
ModelMatch: stop flying the wrong model Spektrum
Spektrum ModelMatch is automatic: a receiver only answers the model memory it was bound with. Use it, do not fight it.
- Every airplane gets its own model memory. Select the model first, then bind the receiver to it.
- With another model selected the receiver will not respond. That is ModelMatch doing its job, not a fault.
- Copying a model does NOT copy the bind. The same goes for resetting a model, changing its Model Type or importing a model file: bind again afterwards.
- Check the model name on the main screen before every flight.
- Test: select a different model on the radio. The airplane must NOT respond to the sticks.
- DXS: there is no model memory, so ModelMatch does not help you. One DXS per airplane, or re-bind each time you change.
Control-surface direction check EdgeTX
Reversed controls are the most common cause of crashes right after takeoff.
- Stand behind the airplane, looking forward the way the pilot would.
- Aileron stick RIGHT: right aileron goes UP, left aileron goes DOWN.
- Elevator stick BACK (pulled toward you): elevator goes UP.
- Rudder stick RIGHT: rudder trailing edge moves RIGHT.
- Flying wing: stick back = both elevons up; stick right = right elevon up, left elevon down.
- If a surface is wrong, reverse that channel on the radio's Outputs page (Direction: INV), never by swapping servos around.
- Check flight-stabilized receivers too: tilt the airplane and confirm the gyro corrects in the right direction.
Control-surface direction check Spektrum
Reversed controls are the most common cause of crashes right after takeoff.
- Stand behind the airplane, looking forward the way the pilot would.
- Aileron stick RIGHT: right aileron goes UP, left aileron goes DOWN.
- Elevator stick BACK (pulled toward you): elevator goes UP.
- Rudder stick RIGHT: rudder trailing edge moves RIGHT.
- Flying wing: stick back = both elevons up; stick right = right elevon up, left elevon down.
- Set the wing and tail type first (System Setup or Model Setup > Aircraft Type). For a V-tail or flying wing, if the mixed surfaces are wrong, try the other version (V-Tail A or B, Elevon A or B) before reversing anything.
- To reverse a channel: NX and DX radios, Function List > Servo Setup, scroll left from Travel to Reverse, then pick the channel. iX radios: Model Adjust > Servo Setup > Reverse.
- After any reversing, re-bind so the failsafe positions are stored again. Reversing the throttle makes the radio warn you about this.
- AS3X and SAFE: tilt the airplane and check that the gyro corrects AGAINST the movement (nose dips, elevator goes up). On AR631+ receivers, run Forward Programming > Gyro Settings > System Setup > Utilities > Gyro Response Test. If you changed reversing after the gyro setup, run Relearn Servo Settings there too.
- DXS: reversing is done with trim programming at power-up. Follow the DXS manual.
Range / link check EdgeTX
Confirm the link is healthy before you fly.
- FrSky and multi-protocol modules: use Range Check in the RF settings. It lowers output power so you can walk about 30 m (100 ft) away with controls still responding.
- ExpressLRS has no reduced-power range mode. Instead, walk away with telemetry on and watch Link Quality (LQ) and RSSI; LQ should stay near 100% at ground level near the field.
- Point receiver antennas in different directions (90° apart on diversity receivers) and keep them away from carbon fibre and metal.
- If you see servo glitches or telemetry warnings during the check, don't fly. Find the cause first.
Range / link check Spektrum
Confirm the link is healthy before you fly.
- NX and DX radios: Function List > Range Test. On that screen, hold the trainer button: the screen shows reduced power and stays there until you let go. Telemetry alarms are off during the test.
- Distance on NX radios: about 30 paces (28 m) from the restrained airplane, holding the radio as you would to fly. Other DX radios may give a different distance in their manual.
- iX radios: Model Setup > Range Test, then follow the steps on screen. Scroll to the bottom of that screen for the Flight Log numbers.
- Have a helper hold the airplane, motor in cut. Walk away while they watch the surfaces. Every surface should follow the sticks smoothly with no stutter.
- With a telemetry receiver, look at the Flight Log afterwards: a few fades are normal; frame losses that climb fast, or any hold, are not.
- Receivers with more than one antenna, or a remote receiver: point the antennas in different directions (about 90 degrees apart) and keep them away from carbon fibre, metal and batteries.
- If you see glitches during the check, don't fly. Find the cause first.
Open this in Maiden Flight Free to start. Works on phone and computer.