Maiden Flight Open the app

Maiden Flight › Setup guides › RadioMaster & EdgeTX

Failsafe in depth

Failsafe decides what the airplane does when it can't hear the radio. Set it for every model, and prove it on the bench before the first flight. About 20 min. For: RadioMaster / EdgeTX.

You need

What failsafe does

  1. When the receiver stops getting valid packets, it switches to its failsafe outputs. On an electric airplane the one that matters most is throttle: it must go to idle or off.
  2. Hold (last position) keeps every output where it was. For throttle that can mean a motor running at whatever you last commanded. Don't use Hold for throttle.
  3. Custom sends a fixed value you choose for each output: throttle idle, gear down, surfaces at a gentle setting.
  4. No pulses stops sending servo signals. Servos go limp and most ESCs stop the motor, but not all ESCs do it promptly. Only trust it after testing with your ESC.
  5. Which options you get depends on the receiver and protocol. The rule never changes: throttle to idle, then test.

ExpressLRS PWM receivers

  1. Failsafe is set per output in the receiver's web settings (WiFi), not on the radio. Each output has its own value in microseconds, from about 988 to 2012.
  2. Out of the box every output fails to 1500 us (centre), except output 3, which fails to 988 us (throttle low with a normal CH3).
  3. Change any output that must not go to centre: retracts, doors, flaps, a second motor, or a throttle that isn't on output 3. To find a value, put the control where you want it, read that channel on the Channel Monitor, and convert: -100 is about 988 us, 0 is 1500 us, +100 is about 2012 us.
  4. The receiver enters failsafe when link quality reaches 0, or after about 1 second without a valid packet, whichever comes first.
  5. At power-up an ExpressLRS PWM receiver sends no pulses until the radio connects. Servos stay limp and the ESC won't arm until then, which is normal.

ExpressLRS serial receivers (flight controller or gyro)

  1. A serial receiver doesn't hold servo positions itself. It passes channels to a flight controller or stabiliser, and that device decides what to do on signal loss.
  2. Set failsafe in that device's own software or menu. Throttle should go to idle (or the device's return or land mode, if it has one and you've set it up).
  3. Check the device detects the loss: switch the radio off and watch its status or LEDs. Some only react after a set delay.

FrSky and other receivers via the internal module

  1. Model Setup > Internal RF > Failsafe. Options typically include Not set, Hold, Custom, No pulses and Receiver. The exact list and names vary by protocol and version.
  2. Choose Custom. Put the throttle at idle with the cut switch in CUT, then use the option to copy the current outputs into failsafe (its name varies). Adjust any channel that needs a different value.
  3. Check CH3's failsafe value matches what the Channel Monitor shows for CH3 at idle with the cut on.
  4. FrSky D8 receivers usually store failsafe in the receiver itself: you set it with the receiver's button. Follow its manual, then test it the same way.

Not set is not the same as safe. Some receivers then hold the last position. Always choose a setting on purpose.

Test it, every model

  1. Propeller off, airplane held or strapped down. Power up the radio first, then the airplane.
  2. Arm, raise the throttle a little, and put any retracts, flaps or doors in a non-failsafe position.
  3. Switch the RADIO off. Within about a second the motor must stop and every other output must go to its failsafe position.
  4. Before switching the radio back on, put the throttle stick down and the cut switch in CUT. When the link returns, the receiver follows your sticks again straight away.
  5. Repeat the test after any receiver firmware update, output remap or receiver swap.

Example

ELRS PWM failsafe (receiver web settings)
  Output 1 Ail    1500 us  (centre)
  Output 2 Ele    1500 us
  Output 3 Thr     988 us  (default: idle with a normal CH3)
  Output 7 Gear   2012 us  (gear DOWN, read from Channel Monitor +100)
CH3 reversed in Outputs: output 3 idle is about 2012 us, not 988.

Check: you're done when

Open this in Maiden Flight Free to start. Works on phone and computer.