Maiden Flight › Setup guides › RadioMaster & EdgeTX
Your first mixes
A mix decides what drives each channel. Learn to read the Mixes screen and add one line, and the advanced guides stop looking like code. About 15 min. For: RadioMaster / EdgeTX.
You need
- A model with CH1-CH4 working (guides 3-6 done)
- Propeller removed
- A spare servo on CH6 is handy for practice
What a mix is
- Each channel (CH1, CH2...) is a list of mix lines. Each line takes a source, such as a stick input or a switch, and adds it to that channel.
- The order in the radio is Inputs (your sticks, with rates and expo) > Mixes (which channel each one drives) > Outputs (servo direction and end points).
- A new model already has four mixes: CH1 from Ail, CH2 from Ele, CH3 from Thr, CH4 from Rud. You built on these in the earlier guides.
- For the full picture, see 'How EdgeTX builds a channel' in the EdgeTX deep dive.
Read the Mixes screen
- Open MDL and page to Mixes. Each row shows the channel, the source, the weight (as a %), and any switch, curve or flight mode on that line.
- Lines under the same channel are combined. A plain line adds to the ones above it (shown as += or ADD, depending on the radio).
- Sources marked with an I and a number (shown as [I1]Ail or similar, depending on the radio) are your Inputs. Use these rather than the raw stick, so your rates and expo still apply.
- Black-and-white radios fit less on screen: scroll sideways or open a line to see all its fields.
Add a line: aileron-to-rudder
- A small rudder mix from aileron helps many high-wing trainers and scale models turn cleanly. It's a good first mix.
- Select CH4 and add a new line below the existing Rud line. On most versions you long-press the line (or tap it on a touchscreen) and choose Insert after. The exact wording varies.
- Set Source to your aileron input, Weight to 20%, and leave Offset at 0.
- Return to the Mixes list. CH4 now has two lines: Rud 100% and Ail 20%.
- Bench check from behind the airplane: right aileron stick should also move the rudder trailing edge a little to the right. If it goes left, change the weight to -20%.
Weight, offset and a switch
- Weight scales the source. 100% passes it through, 50% halves it, and a negative weight reverses it on that line only.
- Offset shifts the line's result up or down. It is added after the weight. Use it for fixed positions, not for centring servos (that's subtrim or the linkage).
- Switch makes the line work only when that switch position is on. Put the aileron-to-rudder line on a free switch so you can try the airplane with and without it.
- A switch can also be the source. CH6 += a 2-position switch at weight 100 moves a servo from one end to the other: the basis for a tow release or drop. Switches read -100 in the UP position and +100 DOWN (0 in the middle on a 3-position switch).
Prove it on the monitors
- Open the Channel Monitor and move the aileron stick: CH1 moves fully and CH4 moves a little. Flip the mix switch: the CH4 movement appears and disappears.
- The Mixes Monitor (on radios that have it) shows each mix line's result as you move sticks, which is useful when a channel does something unexpected.
- Then check the airplane itself, from behind, with the propeller removed.
- If a channel goes beyond what the servo can do, reduce the mix weights first. Outputs Min/Max set the servo's travel limit and are the last step, so nothing can push the servo past them.
Example
CH4 Rudder += [I4]Rud weight 100 += [I1]Ail weight 20 switch SE-down (aileron-to-rudder) CH6 Release += SA weight 100 (UP = -100, DOWN = +100)
Check: you're done when
- You can say what each line on CH1-CH4 does.
- Your new mix line moves the right servo, the right way.
- The mix switch turns the line on and off on the Channel Monitor.
- No servo buzzes at full stick with the mix active.
Open this in Maiden Flight Free to start. Works on phone and computer.