Receivers explained
The receiver is the radio's other half. Pick the right type, power it properly and place its antennas well, and most link problems never happen. About 12 min. For: All radios.
You need
- Your receiver and its manual or product page
- Your radio (to check which RF module it has)
PWM or serial?
- A PWM receiver has a row of servo pins, one per channel. Servos and the ESC plug straight in. This is what most airplanes use.
- A serial receiver has one small connector that carries every channel down a single wire. CRSF is the ExpressLRS (and Crossfire) format and also carries telemetry back. SBUS is an older one-way format used by FrSky and many gyros.
- Serial receivers need something to decode them: a flight controller, a stabiliser or gyro unit, or a serial-to-PWM adapter. They can't drive servos on their own.
- Some receivers can do both. Many ExpressLRS PWM receivers can turn a pair of pins into a serial port in their web settings. Check yours before buying an extra one.
How many channels? EdgeTX
- Count what moves: aileron, elevator, throttle, rudder is 4. Two aileron servos on separate channels, flaps, retracts and doors each add more.
- Buy for the airplane you'll have next year, not just this one. A 6- or 8-output receiver costs little more than a 4.
- ExpressLRS: channels 5 and up behave differently depending on the packet rate. If any servo sits on CH5 or higher, read the 'ExpressLRS start to finish' guide before you fly.
- The radio can send more channels than the receiver has pins. Unused channels are simply ignored.
How many channels? Spektrum
- Count what moves: aileron, elevator, throttle, rudder is 4. Two aileron servos on separate channels, flaps, retracts and doors each add more.
- On Spektrum the wing and tail type decides where the extra servos go. A Dual Aileron wing, for example, uses CH6 for the second aileron, so count those channels too.
- Buy for the airplane you'll have next year, not just this one. A 6- or 8-output receiver costs little more than a 4.
- The radio can send more channels than the receiver has pins. Unused channels are simply ignored.
Powering the receiver
- Most electric airplanes power the receiver from the ESC's BEC through the throttle lead. Nothing extra is needed.
- Check two numbers: the BEC voltage must suit both the receiver and the servos (standard servos vs high-voltage servos), and the BEC current rating must cover all your servos moving at once.
- Larger models, gliders and fuel engines often use a separate receiver battery or a standalone BEC. Use a switch or a plug you can't knock loose.
- Two ESCs (twins): connecting two BECs to one receiver is usually not recommended. A common fix is to use one BEC and disconnect the red wire on the other ESC's lead. Check both ESC manuals.
- A receiver that browns out looks exactly like a lost link. If you have voltage telemetry, watch RxBt while you move every servo at once on the bench.
Check the receiver's input voltage range on its product page before connecting a high-voltage BEC or a 2S receiver pack.
Antenna placement
- The part that receives is the thin exposed tip at the end of the antenna lead. Keep that tip clear of carbon fibre, metal, batteries and ESC or motor wires.
- Receivers with two antennas (diversity): point them about 90 degrees apart, for example one along the fuselage and one across it or upright.
- Never cut, coil or tightly kink an antenna lead. Use the length it came with.
- In a carbon or foil-covered fuselage, route the tips outside through small tubes.
- Fix the receiver so it can't move, and keep the antenna tips away from the receiver body's own wiring.
Which receivers work with your radio EdgeTX
- Radio with an internal ExpressLRS module: use ExpressLRS receivers of the same band (2.4 GHz with 2.4 GHz). Internal RF is set to CRSF.
- Radio with a CC2500 module: FrSky D8 and D16 (ACCST) receivers and a few other CC2500 protocols such as Futaba S-FHSS. Internal RF is set to MULTI. FrSky ACCESS receivers don't work with it.
- Other protocols need a full 4-in-1 multi-protocol module, either built in or in the external bay.
- Not sure which module you have? SYS > Tools shows an ExpressLRS script on ELRS radios, and Model Setup > Internal RF lists the modes your radio offers.
Check: you're done when
- You know whether your receiver is PWM or serial, and how many outputs it has.
- Your BEC or receiver pack suits the receiver and servos, in voltage and current.
- Antenna tips are clear of carbon, metal and power wiring, and about 90 degrees apart on a two-antenna receiver.
- Your receiver's protocol matches your radio's RF module.
Open this in Maiden Flight Free to start. Works on phone and computer.